ColorBar Double Bar screw down snow rail installed on an exposed fastener metal roof
ColorBar Double Bar Screw Down Snow Rail for Exposed Fastener Metal Roofs – 6 Foot Aluminum (Canada)
9" Panel Flat (Bracket Every 18") Wood Purlins
$379.00 CAD
Passer aux informations sur le produit
ColorBar Double Bar screw down snow rail installed on an exposed fastener metal roof

ColorBar Double Bar Screw Down Snow Rail for Exposed Fastener Metal Roofs – 6 Foot Aluminum (Canada)

$379.00 CAD
Seam Spacing

Canada Snow Guards · Genuine SnoBlox-Snojax

Canadian stock — Paris, ONCAD pricing · No dutiesLifetime system warrantyFree engineered layouts

Two colour-matched 6061-T6 aluminum ColorBar rails on every bracket, built for exposed-fastener metal roofs that need more than a single bar. Each double bar bracket sits on an MRM screw-down base fastened through the panel flat into structural wood or steel purlins, so the load goes into the frame and not the panel skin. The lower bar holds the base of the snowpack, the upper bar catches the layer riding above it, and both bars take a colour strip so the system reads as part of the roof.

Volume pricing — applied automatically in cart

Qty 9″ panel 12″ panel
1–9 $379.00 each $399.00 each
10+ $315.63 each $332.29 each — save 16.7%
25+ $290.28 each $305.59 each — save 23.4%
50+ $264.92 each $278.90 each — save 30.1%
100+ $247.18 each $260.23 each — save 34.8%

Mix and match: every snow bar and rail in your cart counts toward the same quantity break.

When does a screw-down roof need a ColorBar Double Bar instead of a single bar?

A single screw-down bar holds the base layer, and on a moderate roof that is often enough. Go to the double bar when the roof is steep, the ground snow load is heavy, or the building is commercial or high-visibility and a release is not an option. It is also the pick for coastal or corrosive sites, because aluminum does not rust, and for any roof where the retention has to match the panel colour.

If your snow load is moderate and colour match is not a concern, the single Screw Down ColorBar or the galvanized Screw Down Double Bar may be all you need. Send us the roof and we will tell you which one it calls for.

What makes the ColorBar aluminum rail different from a galvanized snow bar?

Each ColorBar is an extruded 6061-T6 structural aluminum section with three internal support ribs and a flat front face. It will not bleed rust down a coated panel from a cut end or a fastener contact point, and the sealed extrusion needs no plastic end caps. The bars ship in mill aluminum finish, with full powder coating available by quote.

How do you colour-match a ColorBar Double Bar to your metal roof?

The front face of each bar has a 2-inch channel. A colour strip slides into it and holds by friction, with no extra fasteners. You can order ColorBar colour strips in common roof colours, or cut your own from leftover flat stock from the roof install for an exact match. A double bar kit has two bars, so plan on 12 ft of strip for every 6 ft kit.

How the ColorBar Double Bar fastens to an exposed-fastener roof

Exposed-fastener roofs have no seam to clamp, so this system is screwed down, and that only works when the screw reaches structure. The MRM base sits on the panel flat between the minor ribs, centred over a purlin, and is fastened through every base hole with screws that carry bonded sealing washers. The aluminum double bar bracket bolts on top, the two ColorBars slide through its lower and upper receivers, and Tek screws lock the bars to the brackets.

Which ColorBar Double Bar kit matches your panel and purlins?

Two things decide your variant. First, your panel width: a 9″ flat takes a bracket every 18″, a 12″ flat takes one every 12″. Second, what you are screwing into, wood purlins or metal purlins, which changes the fastener that ships with the kit. If you do not know your panel width, measure flat-to-flat between two ribs and send us a photo. We will confirm it before you order.

Metal roofs the ColorBar Double Bar screw-down system fits

  • Exposed-fastener / screw-down metal roofs: PBR, R-panel, AG panel, 5V crimp, Tuff Rib, Classic Rib, U-panel and similar ribbed profiles
  • 9″ and 12″ flat panel widths
  • Wood purlins or metal purlins (select your fastener package above)
  • Panels of at least 26 gauge over wood purlins or 24 gauge over steel purlins, with sound, properly driven panel fasteners
  • Not for standing seam roofs. Use the clamp-on ColorBar Double Bar for standing seam instead

What's included in each 6 ft ColorBar Double Bar kit

  • (2) 1.8 m (6 ft) extruded 6061-T6 aluminum ColorBars, mill finish, each with a 2-inch colour strip channel
  • MRM screw-down mounting brackets at your selected spacing
  • Aluminum double bar brackets that mount on the MRM bases and carry both bars
  • Purlin fasteners with bonded sealing washers: 1.5″ Master Driller screws for metal purlins or 2″ Master Gripper screws for wood purlins
  • Tek screws to secure the bars to the brackets
  • Aluminum splice connectors for continuous runs
  • Installation instructions with photos

Colour strips and powder coating are ordered separately.

ColorBar Double Bar screw-down specifications

Rails Two extruded 6061-T6 aluminum ColorBars per 1.8 m (6 ft) kit, three internal support ribs per bar, joined end-to-end across the roof face
Finish Mill aluminum, 2-inch colour strip channel on the face of each bar. Powder coat by quote
Mounting MRM screw-down base plus aluminum double bar bracket, fastened through the panel flat into structural purlins
Panel fasteners 1.5″ Master Driller (metal purlins) or 2″ Master Gripper (wood purlins), bonded sealing washers
Bracket spacing 9″ panel: every 18″ · 12″ panel: every 12″
Minimum panel 26 gauge over wood purlins · 24 gauge over steel purlins
Splicing Aluminum splice connectors, included
Warranty Lifetime system warranty when installed to the engineered layout
Single-bar alternative Screw Down ColorBar from $275
Galvanized alternative Screw Down Double Bar from $355, two 1 in × 1 in galvanized steel bars
Origin & stock Stocked in Paris, Ontario

ColorBar Double Bar installation rules to know before you order

  • Every row lands on a purlin. Locate your purlins first, because bracket placement follows the structure and not the panel pattern.
  • Without an engineered layout, the first row goes 12″ up from the eave, or over the bearing wall or first purlin.
  • Bars run no more than 3″ past the last bracket, and any short section must span at least two brackets.
  • Splice connectors go between brackets, never inside one. Butt the bar ends within 1/8″, screw the connector to one bar only and let the other end float for thermal movement.
  • This is a full-roof system. It is not designed for isolated runs over a doorway, vent or chimney, and an upper roof needs snow retention before the roof below it does.
  • A snow rail is not a fall protection anchor. Tie off to a rated anchor while you install.

ColorBar Double Bar installation instructions, spec sheet and cut sheet

Why buy your ColorBar Double Bar from Canada Snow Guards

We're the authorized Canadian SnoBlox-Snojax distributor: genuine product with the manufacturer's warranty behind it, not grey-market imports. Inventory lives in Paris, Ontario and ships to every province and territory in Canadian dollars, with no duties, no brokerage fees and no border delays.

Not sure how many kits you need? Send your roof dimensions, pitch, panel profile and town for a free engineered layout and warrantied quote, matched to your local ground snow load (NBCC Ss/Sr), usually back within one business day.

Get my free warrantied layout →

Vous pourriez aussi aimer