Canada Snow GuardsHow many do I need? / Snow guard calculator

Snow Guard Calculator for Metal Roofs

A free snow guard calculator for Canadian metal roofs. Pick your snow guard, choose how it attaches, enter your roof measurements, and get the rows, guard count, layout and price in Canadian dollars.

Need a continuous snow rail instead? Use the snow rail calculator.

01

Which snow guard do you want on your metal roof?

02

How do you want to attach your snow guards?

03

How many snow guards does your roof need?

Rows0
Per row0
Total guards0
Estimate in CAD$0.00
Add to cart
View product

How far apart should snow guard rows be on each roof pitch?

Row spacing tightens as the roof gets steeper. These are the maximum distances between staggered rows, in feet, for ground snow loads up to 45 PSF (2.15 kPa).

What if your ground snow load is over 45 PSF?

Individual pad-style snow guards are rated for ground snow loads up to 45 PSF, which is 2.15 kPa. Above that, a continuous rail system such as SnoBar or ColorBar is the right fit. Call 437-475-2066 or visit canadasnowguards.com for a rail layout, or size a rail system with the snow rail calculator.

What do you need to measure before ordering snow guards?

Four numbers drive the whole layout. Take them once and the calculator does the rest.

Eave length

The length of the roof edge the snow slides toward, in feet. This sets how many guards go in each row.

Run from ridge to eave

Measure up the slope along the panel, from the eave to the ridge. Do not use the floor plan dimension. Longer runs need more rows.

Roof pitch

The rise in inches over 12 inches of run. A 6/12 roof sheds snow harder than a 3/12 roof, so its rows sit closer together.

Panel flat width

The flat between two ribs or seams. Flats up to 16 inches take one guard. Flats 17 to 24 inches take two.

Should you glue down or screw down your snow guards?

Your panel type decides it. Standing seam panels float as they expand and contract, so they should never be screwed through. Exposed-fastener panels such as PBR, R-panel and ag panel can take either method.

Glue-down snow guards with SB-190 adhesive

  • No holes in the roof panel.
  • Surebond SB-190 is the only adhesive recommended for polycarbonate guards.
  • Full cure takes about 28 days at 10°C (50°F), so install in warm weather.
  • The Snojax I is the one clear guard that cannot be glued.

SB-190 adhesive tubes

Screw-down snow guards with screws and sealant

  • Each polycarbonate guard takes two screws.
  • Use 2 inch #14 screws into wood purlins and 1.5 inch #14 screws into metal purlins.
  • Cover the whole base with NovaFlex MR150 sealant before fastening. It is a sealant, not an adhesive.
  • For exposed-fastener panels only.

NovaFlex MR150 sealant

Snow guard spacing and quantity questions

How many snow guards do I need for a metal roof?

It depends on roof pitch, the run from ridge to eave, and panel width. Divide the run by the row spacing for your pitch and round up to get the rows, then allow one guard per panel flat in each row, or two on flats 17 to 24 inches wide. A 40 ft eave with a 20 ft run at 4/12 pitch on 16 inch panels works out to 60 glue-down guards in 2 staggered rows.

Can you put snow guards on a standing seam metal roof?

Yes, but never with screws. Standing seam panels float as they heat and cool, so use glue-down guards on the panel flat or a SnoCleat RC that clamps to the seam.

How long does SB-190 snow guard adhesive take to cure?

Surebond SB-190 needs about 28 days at 10°C (50°F) for a full cure. Colder spells pause the cure and stretch that time, so plan glue-down installs for the warm months.

How many snow guards does one tube of SB-190 cover?

One tube attaches roughly 20 to 25 of the smaller polycarbonate guards, or about 10 of the larger ones. Coverage varies with how the adhesive is applied.

Is one row of snow guards at the eave enough?

Rarely. One row carries the whole snowpack by itself. Staggered rows repeated up the roof share the weight, which is why the calculator adds rows as the run gets longer or the pitch gets steeper.

What happens if a glue-down snow guard is overloaded?

In conditions beyond the designed layout, a glued guard will usually release from the panel instead of damaging it or causing a leak, and it can be glued back in the same spot.

Can you calculate more than one roof area?

Yes. Enter the first roof area, press Add another roof area and enter the next one. The calculator adds every area into one estimate and one cart.

Estimates are for preliminary planning. Results assume a staggered up-and-down pattern across the full roof with 9 to 12 inches between guards, and never more than 16 inches. Do not place guards only over doors or vents unless you are using the doorway layout. Confirm your panel profile and snow load before ordering.Free shipping applies to orders over $299 for a limited time. Your cart confirms it at checkout.Prices in CAD from canadasnowguards.com, checked 19 November 2026. Taxes and shipping are extra.