Canada Snow GuardsHow many do I need? / Snow rail calculator

Snow Rail Calculator for Metal Roofs

A free snow rail calculator, also called a snow bar calculator, for Canadian metal roofs. Choose the economical 1 in x 1 in SnoBar or the colour-matched ColorBar, single or double bar, and your roof type. Enter your roof and snow load to get the rows, 6 ft kit count, layout and price in Canadian dollars.

SnoBar: the economical 1 in x 1 in snow railSave up to 34.8% with volume pricingFree shipping over $299

Looking for individual snow guards? Use the snow guard calculator.

01

SnoBar or ColorBar: which snow rail do you want?

02

Do you want a single bar or a double bar?

03

Is your metal roof standing seam or screw-down?

04

How many snow rail rows does your roof need?

Rail rows0
Per row06 ft kits
Total kits0
Estimate in CAD$0.00
Add to cart

How is snow rail row spacing calculated?

The steeper the roof and the heavier the snow, the harder the snowpack pushes downslope. The calculator works out that sliding force per panel, compares it with what each clamp or bracket can hold, and sets the widest row spacing that stays inside that limit. The first row sits 1 ft above the eave and the rest are spread evenly up the roof.

AttachmentHolds per clamp or bracket
SnoBar clamp, steel panels to 19 in500 lb
SnoBar clamp, steel panels over 19 in400 lb
ColorBar clamp, steel panels to 24 in700 lb
Any clamp on aluminum or copper panels300 lb
Screw-down bracket, metal purlins400 lb
Screw-down bracket, wood purlins250 lb

How much do you save with volume pricing on snow rail kits?

The more 6 ft kits a roof needs, the less each one costs. The discount is automatic in your cart, with no code to enter.

Kits in your cartYou save
1 to 9List price
10 to 2416.7% off every kit
25 to 4923.4% off every kit
50 to 9930.1% off every kit
100 or more34.8% off every kit

Kits mix and match. SnoBar, ColorBar, single bar and double bar kits all count toward the same quantity break, and orders over $299 ship free for a limited time.

SnoBar or ColorBar: which snow rail suits your roof?

SnoBarColorBar
Best forThe economical choiceMatching the roof colour
Rail1 in x 1 in square tube in galvanized steelExtruded 6061-T6 aluminum bar
Colour matchGalvanized mill finishAccepts a snap-in colour strip to match the roof
Clamp limit on steel panels500 lb to 19 in seams, 400 lb wider700 lb to 24 in seams

SnoBar is the economical snow rail. It is a plain 1 in x 1 in galvanized steel tube with no colour strip to buy, and it is our lowest-priced standing seam rail kit. Choose ColorBar when the rail needs to match the roof. ColorBar holds more per clamp, so on some roofs it needs fewer rows. Run both in the calculator and compare the totals.

When should you choose a snow rail over individual snow guards?

  • Your ground snow load is over 45 PSF (2.15 kPa). Individual guards are rated up to that load. A rail system is designed to your actual load.
  • You have a standing seam roof and do not want adhesive. Rail clamps grip the seam with no holes and no cure time.
  • The roof is steep or the run is long. A double bar puts two rails in each row for a taller barrier.

For lighter loads and smaller roofs, individual guards usually cost less. Price them with the snow guard calculator.

Where do you find your ground snow load in Canada?

The National Building Code of Canada publishes a ground snow load for hundreds of locations, listed in kilopascals. Your municipal building department can confirm the figure for your address. Enter it in kPa and the calculator converts it, at 20.9 PSF per kPa.

Do you need IceStoppers on a standing seam snow rail?

IceStoppers are an add-on for standing seam rail systems. They fasten to the back of the rail without piercing the panel and keep low-lying snow and ice from sliding underneath it. They are strongly recommended above doors, walkways and anywhere people pass below. Tick Add IceStoppers in the calculator and every standing seam kit comes with them: 6 per kit on 12 in seams, 5 on 16 in, 4 on 18 in and 3 on 24 in. We confirm your seam height after you order so they fit.

Snow rail layout questions

Which snow rail is the most economical?

SnoBar. It is a 1 in x 1 in galvanized steel rail and our lowest-priced standing seam rail kit. Volume pricing lowers the cost of every kit further once a roof needs 10 or more.

What roofs can take a snow rail?

SnoBar and ColorBar rails mount on standing seam, screw-down, PBR and 2.67 corrugated metal roofs. This calculator covers those. For shingle, membrane or slate roofs, call 437-475-2066 for a layout.

Can you screw a snow rail into a standing seam roof?

No. Standing seam panels must stay free to move, so the rail attaches with clamps that grip the seam and leave the panel unpunctured.

How far above the eave does the first snow rail go?

The first row sits 1 ft up from the eave. Any further rows are spaced evenly between that row and the ridge.

How long is a snow rail kit?

Kits are 6 ft long. The calculator rounds each row up to full kits, so a 40 ft eave takes 7 kits per row.

Why does the calculator ask for the roof panel material?

Aluminum and copper panels are softer than steel. Each clamp is limited to 300 lb on those panels, which moves the rows closer together.

Can you calculate more than one roof area?

Yes. Enter the first roof area, press Add another roof area and enter the next one. The calculator adds every area into one estimate and one cart, so volume pricing counts every kit.

Estimates are for preliminary planning. Rails must run the full width of the roof area, never only over a door or vent. Confirm your panel profile, seam type and ground snow load before ordering, and call 437-475-2066 for a reviewed layout on large or complex roofs.Volume pricing and free shipping over $299 are current offers and are confirmed in your cart at checkout.Prices in CAD from canadasnowguards.com, checked 19 November 2026. Taxes and shipping are extra.